People who have ever taken part in removing graffiti from surface understand that the removal process is harder than applying. Normally the removal method used should depend on the type of surface in question. Various methods have been developed in different parts of the world for this job. However, when in need of the best graffiti removal Aurora is the right place to pay a visit.
Use of chemicals, repainting, scrubbing, emulsification, and sandblasting are some of the commonest removal methods available. This article discusses methods and the surfaces they can be applied on. Graffiti is commonly applied on metallic, masonry, plastic, glass, and wooden surfaces. Different types of surfaces may need various methods to be combined for elegant results to be achieved.
On metallic surfaces, common paint thinners may work well. Such thinners include acetone, mineral spirits, and lacquer thinner. Other chemical products may also do just great. Any remnants of paint can be removed by rubbing it off using bronze or steel wool. Light sandpaper can also be useful. If the graffiti paint was deeply seated and still remains, power washing can eliminate any remnants.
The choice of method to use on wooden surfaces should base on the condition of the wood. Mineral spirit can work fine on un-weathered wood in good state. However, mineral spirits are rendered ineffective on weathered surface because they get absorbed. Paint particles are driven deeper into the wood instead of being removed. The same happens with power washing hence repainting is almost the only best option left.
Light penetrating oil should be applied to wipe plastic surfaces. Clouding and permanent tackiness may be caused by paint thinners hence their use on plastics must be avoided. Sandblasting scores highest among methods that can be applied on plastic surfaces. However, the method can only be applied on plastics that are hard and strong. Some forms of plastics are also cleaned well through rubbing softly using ultra-fine bronze or steel wool.
Masonry surfaces are the most challenging. Such surfaces should be pressure washed at pressures of 3000 psi. Using the right model of a pressure washer, such pressures should remove the graffiti. Sandblasting is the other option to think of if power washing fails. When using sandblasting, one should be careful not to direct the stream of abrasive at a specific point for too long. This etches the surface instead of cleaning it. Painting should be considered as the last option.
Cleaning glass surfaces is tricky because of their fragility. It is also easy to etch the surface using minimum efforts. The best way to avoid breakages and etching is to use a razor blade to scrape the surface. An angle of 30 degrees should be maintained with the surface and the blades should also be placed in a holder. This method works well on glass, having an efficiency of 99 percent. After scrapping paint remnants can be rubbed off using water and ultra-fine bronze wool.
Workers face certain dangers from using some of the techniques named above. As such, one must exercise caution to avoid injuries. Wearing respirators and sunglasses is one of the many ways of avoiding harm.
Use of chemicals, repainting, scrubbing, emulsification, and sandblasting are some of the commonest removal methods available. This article discusses methods and the surfaces they can be applied on. Graffiti is commonly applied on metallic, masonry, plastic, glass, and wooden surfaces. Different types of surfaces may need various methods to be combined for elegant results to be achieved.
On metallic surfaces, common paint thinners may work well. Such thinners include acetone, mineral spirits, and lacquer thinner. Other chemical products may also do just great. Any remnants of paint can be removed by rubbing it off using bronze or steel wool. Light sandpaper can also be useful. If the graffiti paint was deeply seated and still remains, power washing can eliminate any remnants.
The choice of method to use on wooden surfaces should base on the condition of the wood. Mineral spirit can work fine on un-weathered wood in good state. However, mineral spirits are rendered ineffective on weathered surface because they get absorbed. Paint particles are driven deeper into the wood instead of being removed. The same happens with power washing hence repainting is almost the only best option left.
Light penetrating oil should be applied to wipe plastic surfaces. Clouding and permanent tackiness may be caused by paint thinners hence their use on plastics must be avoided. Sandblasting scores highest among methods that can be applied on plastic surfaces. However, the method can only be applied on plastics that are hard and strong. Some forms of plastics are also cleaned well through rubbing softly using ultra-fine bronze or steel wool.
Masonry surfaces are the most challenging. Such surfaces should be pressure washed at pressures of 3000 psi. Using the right model of a pressure washer, such pressures should remove the graffiti. Sandblasting is the other option to think of if power washing fails. When using sandblasting, one should be careful not to direct the stream of abrasive at a specific point for too long. This etches the surface instead of cleaning it. Painting should be considered as the last option.
Cleaning glass surfaces is tricky because of their fragility. It is also easy to etch the surface using minimum efforts. The best way to avoid breakages and etching is to use a razor blade to scrape the surface. An angle of 30 degrees should be maintained with the surface and the blades should also be placed in a holder. This method works well on glass, having an efficiency of 99 percent. After scrapping paint remnants can be rubbed off using water and ultra-fine bronze wool.
Workers face certain dangers from using some of the techniques named above. As such, one must exercise caution to avoid injuries. Wearing respirators and sunglasses is one of the many ways of avoiding harm.
About the Author:
Read more about To Get Cheap Services For Graffiti Removal Aurora Deserves To Be Visited.
